Reply
Thread Tools
Posts: 38 | Thanked: 2 times | Joined on Jan 2014
#1
guys i have problem.. actually its my bad using ios7 theme without font..so the screen stuck..after i restatrt.. is there any guide to fix this..
 
Posts: 635 | Thanked: 1,535 times | Joined on Feb 2014 @ Germany
#2
You could flash the ubiboot kernel onto your phone and start it connected to your PC. So all filesystems will get mounted and you can copy the missing fonts. When finished reflash the orignal kernel. Maybe it can be don without flashing by using the flasher -k option, but i never tried that.
 
Guest | Posts: n/a | Thanked: 0 times | Joined on
#3
try to use the rescue CD
http://wiki.maemo.org/N9/N950_Rescue_CD
 
Posts: 38 | Thanked: 2 times | Joined on Jan 2014
#4
ill try that 1st..
 
DJJonosound's Avatar
Posts: 411 | Thanked: 302 times | Joined on May 2012 @ Australia
#5
If the theme is mine, not having install the fonts should not cause this issue
Did anything else happen to the device when installing? It may be my problem, I suck at compiling deb files. At the absolute worst, the phone would not load the home screen and go into a reboot loop if there was a theme error.
 
Posts: 38 | Thanked: 2 times | Joined on Jan 2014
#6
the error message

device not working properly

too many reboots

hmmm..

it stuck on nokia logo hmm i cant bypass that

Last edited by fendetto; 2014-04-21 at 11:48.
 
DJJonosound's Avatar
Posts: 411 | Thanked: 302 times | Joined on May 2012 @ Australia
#7
Its a reboot loop then.
I hope this can fix it.

Open flasher, enter this, then plug phone in.
Code:
flasher --enable-rd-mode --set-rd-flags=no-lifeguard-reset
You then need to boot. The screen will be black once it finishes loading the boot sequence, as the home screen is not running. Reconnect the device, and then connect using mass storage. Copy the attached constants.ini to the device. Make sure you decompress it on your computer before copying. It removes all of the font requirements from the theme.

Then reconnect and use sync and connect. Using an ssh client of some sort, (linux and mac use terminal and type in ssh as command) ssh into root@192.168.2.15. For mac and linux this is done as
Code:
ssh root@192.168.2.15
Then you need to copy the file across using ssh. This should do the trick provided you put the file in mydocs:
Code:
 cp -i "home/user/MyDocs/constants.ini" "usr/share/themes/Full iOS 7 theme/meegotouch/constants.ini"
You want to copy and replace the file.
If this works, shut the device down, and then type this into flasher and connect device:
Code:
flasher --disable-rd-mode
This should work, I hope.

If there is an error in the cp command, I don't know how to use it properly. I don't use it much. Please correct me if that is so.
Attached Files
File Type: zip constants.ini.zip (2.8 KB, 91 views)

Last edited by DJJonosound; 2014-04-21 at 12:04. Reason: forgot to attach file
 

The Following User Says Thank You to DJJonosound For This Useful Post:
Posts: 38 | Thanked: 2 times | Joined on Jan 2014
#8
link of flasher files dead.. hmm
 
DJJonosound's Avatar
Posts: 411 | Thanked: 302 times | Joined on May 2012 @ Australia
#9
https://coderus.openrepos.net/flasher/
Took me a little while to find bit coderus has it covered
 
Posts: 38 | Thanked: 2 times | Joined on Jan 2014
#10
i cant open flasher ...it auto closed hmm

Last edited by fendetto; 2014-04-21 at 12:43.
 
Reply


 
Forum Jump


All times are GMT. The time now is 10:18.