[WIP] Power Half (2000 mAh)
I just got parts for my Power Half from Sparkfun. I'll be using 2000 mAh 3,7 V LiPo as a external battery.
Power Cell will be used for charging the Power Half and converting the 3,7 to 5 V. I'll take the JST connector off and solder the battery straigth to the Power Cell. It's possible to add a SPDT switch into the Power Cell to control its state. Total cost for this set is about 30 eur. There's microusb port in the Power Cell so the Power Half will be charged via it. I have also some 5 mm Copper Tape to connect the power into Jolla. Thickness increase will be about 5.5mm. LiPo at the left side in the picture is 1200 mAh. I don't have enough time this week for prototyping (except taking pics of the parts :D) so you have to wait for next week :) https://pbs.twimg.com/media/BgSUqtAIIAE6pNU.jpg:large |
Re: [WIP] Power Half (2000 mAh)
finally! someone who is gonna give us a battery toh!!
|
Re: [WIP] Power Half (2000 mAh)
IIRC didn't Jolla say that the phone can supply power to the other half? If so couldn't the phone's USB be used to charge the battery making it a lot simpler?
|
Re: [WIP] Power Half (2000 mAh)
Quote:
|
Re: [WIP] Power Half (2000 mAh)
I have also started the project, too
http://talk.maemo.org/showthread.php?t=91895&page=3 The problem with the story is the following: The board what I bought, the charge can not keep up. However, if you use 2 boards, then the charge is very good and quite fast. If we compare times your board with my: Power Cell: 3.3V input Pulolo: 2.5 v-5v input Cell Power: 5V @ 600mA max Pulolo: 5V @ 400/500mA The smartphone itself has a shot of 1000mA. That's why when I connect only a board, he comes after about 30 seconds, no longer with the charging Therefore, the Board is very hot and overheated accordingly. When 2 boards that I use, charging is perfected, but still very hot. Now it would be nice to know if the Power Cell is also very hot and only with a board charging perform continually. The interesting thing about the Power Cell is that he has a Undervoltage lock with it. That is missing in the Pulolo boards. |
Re: [WIP] Power Half (2000 mAh)
I'll report here how it performs when I have tested the board.
|
Re: [WIP] Power Half (2000 mAh)
CSD tool shows about -780 mA and the board gets pretty hot but continues to charge. However, I'll probably find somewhere a boost converter which is capable to ouput 1 A. I have charger-only boards from Adafruit too so I'll just need the 3,7 -> 5 V (1A) boost converter.
Power Cell would work if the current could be limited via Jolla but as far as I can see that is not possible. Of course one can use it, but it gets hot and probably has some efficiency problems at those output levels. Edit: I think this will do: http://www.ebay.com/itm/New-1pcs-1A-...-/191014690726 |
Re: [WIP] Power Half (2000 mAh)
Anything able to throttle down voltage when approaching overload or overheat should work well...
|
Re: [WIP] Power Half (2000 mAh)
i order two now two from them from HK, shipping will take 2-3 weeks :(
|
Re: [WIP] Power Half (2000 mAh)
Wasn't there problems with the charging via the pogo pins? With charging going on and off all the time?
|
All times are GMT. The time now is 21:15. |
vBulletin® Version 3.8.8